![]() What is a good CB base station antenna?.Workman Saturn B100 Base Station Antenna.Sirio SD 27 Dipole CB/10 Meter Base Antenna.Sirio Antenna m400 Tunable Base Antenna.TRAM 1480 Amateur Dual-Band Base Antenna.Our Best CB Base Station Antenna Reviews.Editors' Picks for Top Cb Base Station Antenna in 2022.(SM1L) Chrome plated 90 degree heavy duty stud mount. For use with the (Fire Ring Coaxial Cable) (K4R) The design of the Fire Ring coax termination requires the 1.25" mounting bolt that is found in the K-4R stud mount. The K-4 can be used in any mount or mounting surface with a 1/2" (13mm) hole In a typical installation, antennas with 0.600" (15mm) of exposed threads can be used without the fear of bottoming out before proper tightening is accomplished. (K4) The K-4 stud utilizes ring terminal connectors (supplied)making it compatible with non-PL-259 terminated coaxial cables. Like the K-4, this stud is designed for 1/2" (13mm) holes.3/8" thread bolt The K-4A should be used whenever a PL-259 terminated coax cable is to be used (K-8A, K-9A, R-8A, R-9A). (K4A) Heavy Duty Stud Mount - Steel top, bottom & bolt (PSM1) This mount was designed to bolt to the side of your vehicle. In order to compensate for the door jamb angles, the stud bracket will swivel a full 180 degrees, 90 in each direction. The bracket is 1.5" (38mm) wide and has a 2" (50mm) reach for mounting inside the door jamb. (SS-204A) The bracket and mounting hardware is made of stainless steel. Easily mount your antenna anywhere! Valor Will clamp on to a vertical or horizontal bar due to the 180 degree swivel. (VIC QRCS3) Heavy Duty clamp bracket with 180 degree swivel. All mounting hardware (also stainless steel) is hidden under the vehicles hood After the mount is installed, there will not be any visible mounting holes. The mount allows the antenna to be mounted on either the left or right side of the vehicle. (SS-J4A) This mount was designed around the new Jeep Wranglers body style (97-99). Due to the close quarters, the stud requires crimp-on coaxial connectors. The bracket is 2" (51mm) wide by 4.1" (104mm) long. The bracket has a pre-determined bend and does not interfere with the closing of the hood. (SS-184A) The primary use for the SS-184 stainless steel mount is for antenna installation on the new style Dodge Ram and Dakota pick-ups. Includes stud mount, stainless steel brackets and hardware, and a gasket to protect the vehicle finish. The flat upper bracket is 6" (152mm) long. (SS-194A) Sold OutThose square holes in the bed rails of full size pick-up trucks are the prefect location for a "no-holes" antenna mount. Because of the stud mount configuration on this mount, it can only be used on trucks where there is inside access to the stake hole pocket (from side or bottom) for the coaxial cable to be routed to the mount. There is no need to drill any holes in the vehicle. (SS-294A) Sold Out This stainless steel mount locks into any of the stake hole pockets along the edge of a pick-up truck bed. It stands 1" (25mm) above the vehicle surface without the stud mount, which will add of 2.1" (53mm) when in place. Physically, the mount is 2" (50mm)wide and 2.5" (63mm) deep. Recommended for antennas up to 3ft (92cm). (K-74) The trunk lip bracket slides over trunk edge Two set screws are tightened from the underside to hold the bracket in place. It protrudes outward from the vertical surface 1.9" (48mm). The actual size of the bracket is 2.25" (57mm) wide by 2.9" (74mm) high (4.2" (107mm) with stud). (SS-24A) This bracket is made of heavy-duty stainless steel. The distance between the stainless steel clamping bolts (supplied) allows the mount to span material up to 1.4" (36mm) wide ![]() The upper bracket is 4.6" (117mm) long by 1" (25mm) wide. (SS-134A) This stainless steel mount was specifically designed to mount an antenna on the flat side-view mirror arm supports commonly found on pick-ups. The stud mount hole has a full 1" set back in case you want to replace the stud with one of our Dome Mounts The bracket is 2" (51mm) wide, 5" (127mm) long and 0.100" (2.5mm) thick stainless steel. This mount offers numerous mounting options. (SS-F4A) If your looking for a heavy-duty stainless steel flat mount. This mount may be used with antennas up to 4' (1.2m) long. The supplied stainless steel mounting bolt is a hefty 3/8"-24 x 1" long and includes a stainless steel nut and washers. The bracket itself is about 4" (102mm) long by 1" (25mm) wide. (SS-124A) This mount is our most popular stainless steel mount for flat surface applications. Firestik CB Radio Antenna Brackets & Mountsįirestik high quality CB antenna brackets & mounts
0 Comments
Leave a Reply. |